. Applications

Mine Bonder 2000

Mine Bonder 2000 is an anaerobic adhesive sealant which cures rapidly through large gaps with Hernon Primer 50 and will also provide rapid cure and dry fillets when exposed to high intensity ultraviolet light.

Nuts N' Bolts® 128

Nuts N’ Bolts® 128 is a single component, low strength thread locker designed for locking plastic and metal fasteners. Fixture time is about 5 minutes and adhesive can be pre or post applied. Any excess adhesive on the surface will cure and will not migrate to the other parts. Nuts N’ Bolts® 128 can be used as a low strength thread locker, bonder or tamper proofer for metal, polyester, nylon and many other thermo plastics materials.

Nuts N' Bolts® 220

Nuts N’ Bolts® 220 is a single component, high strength, anaerobic compound used to lock and seal fine threaded nuts, bolts, and studs in a wide variety of applications.

Nuts N' Bolts® 223

Nuts N’ Bolts® 223 is a single component, high strength, anaerobic compound used to lock and seal coarse threaded nuts, bolts, and studs in a wide variety of applications. Each batch of Nuts N’ Bolts® 223 is tested to the lot requirements of CID-A-A 59720 Grade AVV, MIL-S22473E Grade AVV, and to the detail requirements of ASTM D5363 (AN0124).

Nuts N' Bolts® 225

Nuts N’ Bolts® 225 is a single component, high strength, anaerobic compound used to lock and seal coarse threaded nuts, bolts, and studs in a wide variety of applications. Each batch of Nuts N’ Bolts® 225 is tested to the lot requirements of CID-A-A 59720 Grade AV, MIL-S-22473E (Grade AV), and to the detail requirements of ASTM D5363 (AN0123).

Nuts N' Bolts® 227

Nuts N’ Bolts® 227 is a single component, high strength, anaerobic compound used to lock and seal fine threaded nuts, bolts, and studs in a wide variety of applications. Each batch of Nuts N’ Bolts® 227 is tested to the lot requirements of MIL-S-22473E (Grade A), and to the detail requirements of ASTM D5363 (AN0121).

Nuts N' Bolts® 230

Nuts N’ Bolts® 230 is a single component medium strength, anaerobic compound used to lock and seal fine threaded nuts, bolts and studs in a wide variety of applications where removal with ordinary hand tools is necessary. Each batch of Nuts N’ Bolts® 230 is tested to the lot requirements of MIL-S-22473E (Grade B), and to the detail requirements of ASTM D5363 (AN0131).

Nuts N' Bolts® 232

Nuts N’ Bolts® 232 is a single component medium strength, anaerobic compound used to lock and seal fine threaded nuts, bolts and studs in a wide variety of applications where removal with ordinary hand tools is necessary. Each batch of Nuts N’ Bolts 232 is tested to the detailed requirements of ASTM D5363 (AN0141) which replaced MIL-S-22473E (Grade C) specifications.

Nuts N' Bolts® 234

Nuts N’ Bolts® 234 is a single component medium strength, anaerobic compound used to lock and seal coarse threaded nuts, bolts and studs in a wide variety of applications where removal with ordinary hand tools is necessary.

Nuts N' Bolts® 236

Nuts N’ Bolts® 236 is a single component medium strength, anaerobic compound used to lock and seal fine threaded nuts, bolts and studs in a wide variety of applications where removal with ordinary hand tools is necessary. Each batch of Nuts N’ Bolts® 236 is tested to the lot requirements of MIL-S-22473E (Grade CV), and to the detail requirements of ASTM D5363 (AN0142).

Nuts N' Bolts® 237

Nuts N’ Bolts® 237 is a single component, high strength, anaerobic compound used to lock and seal fine threaded nuts, bolts, and studs in a wide variety of applications. Each batch of Nuts N’ Bolts® 237 is tested to the lot requirements of MIL-S-22473E (Grade D), and to the detail requirements of ASTM D5363 (AN0122).

Nuts N' Bolts® 240

Nuts N’ Bolts® 240 is a single component anaerobic compound used to lock and seal fine threaded nuts, bolts and studs in a wide variety of applications requiring easy removal or adjustment. Each batch of Nuts N’ Bolts® 240 is tested to the lot requirements of MIL-S-22473E (Grade E), and to the detail requirements of ASTM D5363 (AN0151).

Nuts N' Bolts® 246

Nuts N’ Bolts® 246 is a single component anaerobic compound used to lock and seal coarse threaded nuts, bolts and studs in a wide variety of applications where removal with ordinary hand tools is necessary. Each batch of Nuts N’ Bolts® 246 is tested to the lot requirements of MIL-S-22473E (Grade HV), and to the detail requirements of ASTM D5363 (AN0162).

Nuts N' Bolts® 248

Nuts N’ Bolts® 248 is a single component anaerobic compound used to lock and seal fine threaded nuts, bolts and studs in a wide variety of applications requiring easy removal or adjustment. Each batch of Nuts N’ Bolts® 248 is tested to the lot requirements of MIL-S-22473E (Grade H), and to the detail requirements of ASTM D5363 (AN0161).

Nuts N' Bolts® 25203

Nuts N' Bolts® 25952

Nuts N' Bolts® 410

Nuts N’ Bolts® 410 is a single component, low viscosity anaerobic adhesive/sealant designed especially for wicking applications. It has the ability to penetrate porous structures and cracks by capillary action, filling voids as large as 0.005 in. Each batch of Nuts N’ Bolts® 410 is tested to the lot requirements of ASTM D5363 (AN0241) and meets the requirements of obsolete MIL-S-46163A (Type III Grade P).

Nuts N' Bolts® 420

Nuts N’ Bolts® 420 is a single component anaerobic thread locking material, which is thixotropic and develops low strength for easy disassembly. The product cures when confined in the absence of air between close fitting metal surfaces. Each batch of Nuts N’ Bolts® 420 is tested to the lot requirements of ASTM D5363 (AN0311) and complies with MIL-S-46163A (Type II Grade M).

Nuts N' Bolts® 423

Nuts N’ Bolts® 423 is a single component anaerobic thread locking material, which is thixotropic and develops medium strength. The product cures when confined in the absence of air between close fitting metal surfaces and is particularly suitable for less active substrates such a stainless steel and plated surfaces. Each batch of Nuts N’ Bolts 423 is tested to the lot requirements of ASTM D5363 (AN0321), and to the detail requirements of MIL-S-46163A (Type II Grade N).

Nuts N' Bolts® 425

Nuts N’ Bolts® 425 is a single component anaerobic thread locking material, which is thixotropic and develops medium to high strength. The product cures when confined in the absence of air between close-fitting metal surfaces.

Nuts N' Bolts® 427

Nuts N’ Bolts® 427 is a single component anaerobic thread locking material, which develops high strength. The product cures when confined in the absence of air between close fitting metal surfaces. UL Classification – File MH14222 Classified by Underwriters Laboratories Inc.® as to fire hazard only. Adhesive/Sealant 427 classed 20 to 30 between kerosene and paraffin oil in respect to fire hazard. Flash point (closed cup) 102.8ºC (217ºF). For use in devices handling gasoline petroleum oils, natural gas (pressure not over 300 psig), butane and propane not exceeding 2 in. pipe size. 29R9. Performance Testing Each batch of Nuts N’ Bolts® 427 is tested to the lot requirements of MIL-S-46163A (Type I Grade K), and to the detail requirements of ASTM D5363 (AN0221).

Nuts N' Bolts® 428

Nuts N’ Bolts® 428 is a single component anaerobic threadlocking compound designed for heavy duty applications subject to operating temperatures to 450°F (232°C). The product delivers high strength locking and sealing on screws, nuts, bolts, studs and fittings. Excellent break-loose and prevailing torque values assure maximized resistance to transverse vibration loosening at elevated temperatures. Meets requirements of CID A-A-59720 Grade HT

Nuts N' Bolts® 429

Nuts N’ Bolts® 429 is a single component anaerobic thread locking adhesive. Nuts N’ Bolts® 429 is a high-strength adhesive for locking and sealing large bolts and studs 1inch and larger diameters. Curing occurs only when adhesive is confined between mating surfaces. The cured adhesive is suitable for temperatures up to 300°F (149°C) and exposure to most solvents. Nuts N’ Bolts® 429 meets the requirements of ASTM D5363 (AN0211) which replaced MIL-S-46163A (Type I Grade L) specifications.

Nuts N' Bolts® 431

Nuts N’ Bolts® 431 is a wicking anaerobic used for preassembled equipment and structures where penetration into fastener connection points is required. This product allows very simple preventive maintenance by permitting thread locking without dismantling equipment. The product “wicks” into voids by capillary action. Use Nuts N’ Bolts® 431 to seal pores or pinhole porosity in welded seams, tanks, castings, or metal parts. The cured adhesive is a thermoset plastic suitable for temperatures up to 400°F (204°C), and exposure to most solvents. Each batch of Nuts N’ Bolts® 431 is tested to the lot requirements of MIL-S-46163A (Type III Grade R), and to the detail requirements of ASTM D5363 (AN0261).

Nuts N' Bolts® 433

Weld Sealant 433 is a single component anaerobic penetrating adhesive and sealant. Utilizing capillary action, Weld Sealant 433 penetrates and seals porosities and cracks as large as 0.127 mm. Once confined away from air Weld Sealant 433 cures to a thermoset plastic. Sealant remaining on the surface will not cure and can be easily wiped clear. Benefits include retention of fluids and pressures as well as corrosion and contamination elimination. Temperature resistance is up to 400°F (204°C). Weld Sealant 433 is impervious to most solvents. Welds, castings and powder metal parts can be sealed to their rupture pressure.

Nuts N' Bolts® 434

Nuts N' Bolts® 434 is a thixotropic, 100% active anaerobic compound which solidifies with reliable and expected strength upon application to most fasteners. Particularly suitable for applications on less active substrates such as stainless steel and plated surfaces, where disassembly with hand tools is required for servicing. Nuts N' Bolts® 434 is easily applied. No mixing (single component), no curing outside the joint and no torque adjustments are necessary. Nuts N' Bolts® 434 offers increased profitability, having approximately 80% cost advantage over the cheapest mechanical methods as well as reducing inventories, maintenance, and the need for costly precision tolerances. Nuts N' Bolts® 434 can be used on up to 3/4inch bolts with light oil contamination.

Nuts N' Bolts® 97860

Nuts N’ Bolts® 97860 is a wicking anaerobic used for preassembled equipment and structures where penetration into fastener connection points is required. This product allows very simple preventive maintenance by permitting thread locking without dismantling equipment. The product “wicks” into voids by capillary action. Use Nuts N’ Bolts® 97860 to seal pores or pinhole porosity in welded seams, tanks, castings, or metal parts. The cured adhesive is a thermoset plastic suitable for temperatures up to 400°F (204°C), and exposure to most solvents.

Powerseal 932

Powerseal 932 is a single component, non-hardening, non-curing gray paste pipe sealant which lubricates and seals threaded pipe connections and O-Rings. Powerseal 932 is unaffected by water, oil, ammonia, glycerin, steam, all types of gases, exhaust fumes and most hard- to- hold liquids. Powerseal 932 withstands extreme temperatures and pressures and will not shrink, crack, or crumble. The product remains pliable and will not harden, making connection vibration proof. It makes for easy assembly and makes disassembly and repair simple. It also prevents corrosion and seizing of metal parts.

Primer 37824

Primer 37824 is a single component, solvent-free, reactive monomer-based product designed to promote the cure speed of Hernon® anaerobic adhesives and sealants. Primer 37824 is used where increased cure speed of Hernon® anaerobic products is required, and for difficult to bond applications where galvanized steel or zinc electroplated surfaces are involved. This product was specially formulated for increasing bond integrity on dichromated surfaces.

Primer 46

Primer 46 is a single component, solvent-free, reactive monomer-based product designed to promote the cure speed of Hernon® anaerobic adhesives and sealants. Primer 46 is used where increased cure speed of Hernon® anaerobic adhesives and sealants is required. It is especially recommended for applications with passive metals or inert surfaces and with large bond gaps. It is particularly recommended for cure conditions below 15°C.

Primer 49

Primer 49 is a single component, non-CFC solvent based product designed to promote the cure speed of Hernon® anaerobic adhesives and sealants. Primer 49 is used where increased cure speed of Hernon® anaerobic adhesives and sealants is required. It is especially recommended for applications with passive metals or inert surfaces and with large bond gaps. It is particularly recommended for cure conditions below 15°C. Primer 49 meets the requirements of MIL-S-22473E (Grade T) and ASTM D5363 (Grade T).

Primer 50

Primer 50 is a single component, non-CFC solvent-based product designed to promote the cure speed of Hernon® anaerobic adhesives and sealants. Primer 50 is used where increased cure speed of Hernon® anaerobic adhesives and sealants is required. It is especially recommended for applications with passive metals or inert surfaces and with large bond gaps. It is particularly recommended for cure conditions below 15°C. Primer 50 meets the requirements of ASTM D5363 (Grade N) and MIL-S-46163A Grade F.

Primer 57

Primer 57 is a single component, solvent-free, reactive monomer-based product designed to promote the cure speed of Hernon® anaerobic adhesives and sealants. Primer 57 is used where increased cure speed of Hernon® anaerobic products is required, and for difficult to bond applications where galvanized steel or zinc electroplated surfaces are involved. This product was specially formulated for increasing bond integrity on dichromated surfaces.

Quantum® 138

Quantum® 138 is a surface insensitive cyanoacrylate adhesive formulated to improve adhesion properties and fixture time as well as gap filling capabilities over conventional cyanoacrylate adhesives. This advanced formulation improves adhesion to wood, leather, ceramics, elastomers, and acidic surfaces such as freshly plated components. Quantum® 138 is a state-of-art single component, solventless, room temperature curing adhesives that polymerize rapidly when pressed into a thin film between parts. The presence of surface moisture commences the cure of the adhesive. Quantum® 138 will develop handling strength within seconds and full cure within a few hours.

Quantum® 156

Quantum® 156 is a single-component cyanoacrylate adhesive formulated for impact, thermal shock and peel resistance.

Quantum® 73421

Quantum® 73421 is a state-of-the-art, single component, solventless, room temperature curing cyanoacrylate adhesive that polymerizes rapidly when pressed into a thin film between parts. The presence of surface moisture commences the cure of the adhesive. Quantum? 73421 develops handling strength within seconds and full functional strength in a few hours. Quantum? 73421 can bond a wide variety of surfaces including metals, thermoplastics, elastomers, ceramics, leather, cork, and paper, but is particularly suited for bonding hard-to-bond plastics. Notwithstanding the superior bonding capability of Quantum? 73421, it is NOT recommended for long-term glass to glass bonding applications.

React® 727

ReAct® 727 is a tough acrylic adhesive designed primarily for securing of ceramic permanent magnet segments in motor magnet bonding applications. This adhesive has also found wide acceptance in a variety of structural bonding applications due to its versatile performance capabilities. ReAct® 727 has demonstrated the ability to provide high tensile strength while maintaining excellent product flexibility. This results in tough, durable bonds with outstanding impact and peel resistance. This tough acrylic is a room temperature curing adhesive which is used in conjunction with Hernon® Activator 56.

React® 730

ReAct® 730 is a high strength non-flammable structural adhesive. This adhesive provides a resilient and rapid cure at room temperature when used with Hernon® Activator 56 or Activator 59. ReAct® 730 will provide high strength bonds on a variety of metals, ceramics, glass, and some plastics.

React® 761

ReAct® 761 is a tough acrylic adhesive designed primarily for bonding permanent magnets. ReAct® 761 has also found wide acceptance in a variety of structural bonding applications due to its versatile performance capabilities. ReAct® 761 provides high tensile strength while maintaining excellent product flexibility. This results in tough durable bonds with outstanding impact and peel resistance. ReAct® 761 is a single component adhesive used in combination with Hernon® Activator 59, Activator 56 or Activator 63 for curing at room temperature. The adhesive may also be heat cured at 150°C.

React® 766

ReAct® 766 is a tough acrylic adhesive designed primarily for bonding permanent magnets. ReAct® 766 has also found wide acceptance in a variety of structural bonding applications due to its versatile performance capabilities. ReAct® 766 provides high tensile strength while maintaining excellent product flexibility. This results in tough durable bonds with outstanding impact and pee1 resistance. Temperature resistance from –40°C (-40°F) to 204°C (400°F). ReAct® 766 is a single component adhesive used in combination with Hernon® Activator 59 or Activator 63 for curing at room temperature. The adhesive may also be heat cured at 150°C.

ReAct® 767

ReAct® 767 is a high performance tough acrylic adhesive designed primarily for securing ceramic permanent magnet segments in motor magnet bonding applications. Used in conjunction with Hernon® Activator 56/ Activator 47, this structural adhesive is ideal for choke and transformer bonding, DC motor assembly, alternator and flywheel applications, tacking, unitizing, ruggedizing, sealing and shallow potting. ReAct® 767 fixtures in seconds, is acrylic acid free and non-corrosive, non-flammable, and suitable for harsh environments. ReAct® 767 exhibits good thermal shock, impact and peel resistance characteristics, and excellent adhesion to a wide variety of plated surfaces.

ReAct® 783

ReAct® 783 is a tough acrylic adhesive designed primarily for bonding permanent magnets. ReAct® 783 has also found wide acceptance in a variety of structural bonding applications due to its versatile performance capabilities. ReAct® 783 is a room temperature curing adhesive, used in combination with Hernon® Activator 59 or Activator 63.

React® 784

ReAct® 784 has excellent bond strength as a structural adhesive. This formulation will offer rapid, high strength and high impact resistant bonds to a variety of substrates within minutes. Designed for a wide variety of substrates. ReAct® 784 is a room temperature curing adhesive, used in combination with Activator 15. This no-mix system allows controlled assembly ideal for production and repair applications. A structural bond develops within minutes.

ReAct® 795

ReAct® 795 is a tough acrylic adhesive designed primarily for securing of ceramic permanent magnet segments in motor magnet bonding applications. This adhesive has also found wide acceptance in a variety of structural bonding applications due to its versatile performance capabilities. ReAct® 795 has demonstrated the ability to provide high tensile strength while maintaining excellent product flexibility. This results in tough, durable bonds with outstanding impact and peel resistance. This tough acrylic is a single component, room temperature curing adhesive which is used in conjunction with Activator 47. Additionally, exposure to a high intensity UV light will cure this adhesive to a dry, hard surface. ReAct® 795 is similar in function to Loctite A533 and Loctite AA332 and delivers high shear strength and tensile strength. One of its primary uses is securing permanent magnets in motor magnet bonding applications. Recomended Applications: Furniture | Elevators | Automotive Applications | Permanent Motor Magnets | Speakers | Generators | Bonding Flywheels | Sensors |

Rust Eliminator 32

Hernon® Rust Eliminator 32 is used for eliminating old rust and preventing new rust on steel parts. Rust is chemically transformed into an inert, non-corrosive coating. Rust Eliminator 32 is used on rusted steel when only minimum surface preparation is practical. Rust Eliminator 32 stops rust, coats surface, and acts as a primer for various covering paints on: • Duct work, overhead cranes, and booms • Municipal and highway signposts • Conveyors, supports, guard rails, fences • Power plants, heating, and cooling plants • Storage tanks, truck trailers • Pipes, valves Product Benefits • Easy to use • Non-flammable, low toxicity • One component • Works on damp, rusty metals • Replaces conventional primers for most industrial finish paints

Rust Inhibitor 40

Rust Inhibitor 40 is an effective corrosion remover and rust preventative which leaves a protective finish for up to 1 year. Produces a clean, dry surface that can be painted, plated or powder coated afterward with no pre-cleaning. Not for use with zinc plated or magnesium items. Rust Inhibitor 40 is used on rusted steel when only a minimum surface preparation is practical. Rust Inhibitor 40 protects, cleans and leaves a protective coating.

Self Locker 523

Self Locker 523 is a pre-applied micro-encapsulated adhesive for threaded fasteners. Self Locker 523 stays dry-to-the-touch until the shearing action of an engaging nut applied to the coated bolt causes the capsules to break allowing the adhesive to cure. This material securely locks and seals against vibration loosening and fluid leakage.

SELF LOCKER 525

Hernon® 525 is a pre-applied, micro-encapsulated adhesive for threaded fasteners. Hernon® 525 stays on the bolt until the shearing action of an engaging nut applied to the coated bolt causes the capsules to break allowing the adhesive to cure. This material securely locks and seals against vibration loosening and fluid leakage. Typical Applications Locking & Sealing: • Head bolts • Truck Axle bolts • Transmission nuts • Pipe plugs and fittings Product Benefits • Improves reliability. • Prevents loosening of bolts due to vibration. • Seals against leakage. • Prevents threads from corroding. • Easily visible for inspection. • Pre-coated parts can be packaged and shipped in normal fashion. • Excellent solvent resistance. •Bonds to stainless steel bolts.

Self Sealer 604

SelfSealer® 604 is a tough, pre-applied, non-hardening threaded sealant. When dried, it becomes a resilient, tight clinging, non-curing sealant for tapered or straight threads. It provides an instant seal on different pipe threads and can be used up to eight (8) times without recoating. SelfSealer® 604 is water based, non-toxic, safe and can be applied easily without special handling precautions. It provides resistance to vibrational loosening because of its prevailing torque characteristics. Therefore, it is very effective on non-locking applications.

Self Sealer 615

SelfSealer® 615 is a high viscosity, tough, pre-applied, non-hardening threaded sealant. When dried, it becomes a resilient, tight clinging, non-curing sealant for tapered or straight threads. It provides an instant seal on different pipe threads and can be used up to eight (8) times without recoating. SelfSealer® 615 is water based, non-toxic, safe and can be applied easily without special handling precautions. It provides resistance to vibrational loosening because of its prevailing torque characteristics. Therefore, it is very effective on non-locking applications.

Applications

Payment options

This website uses cookies.