Curing Method

Quantum® 150 UV is a single component, solventless, room temperature curing cyanoacrylate adhesive with light curing property. The presence of surface moisture and/or light (UV or Visible light) commence the cure of the adhesive. Quantum® 150 UV develops handling strength within seconds and full functional strength within minutes. Quantum 150 UV can bond a wide variety of surfaces including thermoplastics, elastomers. Product Benefits: • Rapid Cure: forms a strong bond by moisture curing at room temperature in less than a minute with contact pressure. • Light curing property: can be easily cured by irradiation with light. Blushing can be also prevented by UV curing. • Surfaces: will bond almost any combination of similar or dissimilar materials. • Easy Use: single component feature, eliminates any mixing. • Due to low viscosity, it can penetrate gaps between surfaces.

Ammunition Primer Sealant 34194 is a single component 100% solid system offering a tough, dry coating with superior chemical and environmental resistance after cure. Ammunition Primer Sealant 34194 will cure rapidly when exposed to high intensity U.V. light. This coating is formulated to migrate rapidly resulting in complete coverage of the gap. The fluorescent sealant will offer an easy inspection using standard vision system.

Cylinlock® 34323 is a fast curing, high-strength anaerobic adhesive yielding higher shear strengths with temperature resistance up to 300°F (149°C) It provides relatively quick cures, outstanding solvent resistance, and improved reliability for metal service applications.

Cylinlock® 42633 is a fast curing, high strength anaerobic adhesive with temperature resistance up to 300°F (149°C). It is designed for the bonding of cylindrical fitting parts, particularly where bond gaps can approach 0.25 mm (0.01 in.) and where maximum strength at room temperature is required. Cylinlock® 42633 provides relatively quick cures, outstanding solvent resistance, and improved reliability for severe service applications.

Cylinlock® 52631 is a single component, anaerobic retaining adhesive designed for the bonding of cylindrical parts. The product cures when confined in the absence of air between close-fitting metal surfaces.

UV Curable Cylinlock® 820 is a fast curing, high-strength anaerobic adhesive designed to retain and seal cylindrical assemblies. Curing occurs when adhesive is confined between mating surfaces. The cured adhesive is a thermoset plastic suitable for exposure to most solvents. Augments or replaces press fits, set screws, pins and other mechanical retaining methods. Avoids heavy press fits due to rapid cure. Cylinlock® 820 cures quickly at room temperature without the need for surface activators or heat to join cylindrical assemblies. Fixturing strength develops in five minutes or within 15 seconds by exposing the edge fillets to high intensity long wavelength UV light (365 nm). Full strength will be reached in 24 hours.

UV Curable Cylinlock® 821 is a fast curing, high strength anaerobic adhesive designed to retain and seal cylindrical assemblies. Curing occurs when adhesive is confined between mating surfaces. The cured adhesive is a thermoset plastic suitable for exposure to most solvents and withstands temperatures up to 300°F (149°C). Augments or replaces press fits, set screws, pins and other mechanical retaining methods. Avoids heavy press fits due to rapid cure. Cylinlock® 821 cures quickly at room temperature without the need for surface activators or heat to join cylindrical assemblies. Fixturing strength develops in five minutes, or within 15 seconds by exposing the edge fillets to high intensity long wavelength UV light (365 nm). Full strength will be reached in 24 hours.

Cylinlock® 822 is a high performance, single component, 100% active anaerobic adhesive/sealant formulated for dependable bonding of fitted cylindrical parts. Cylinlock® 822 offers high strength as well as superior heat and chemical resistant bonding at room temperature. Cylinlock® 822 is formulated for applications, which require superior strength with temperature resistance up to 300°F (149°C). Each batch of Cylinlock® 822 is tested to the lot requirements of MIL-R-46082B (Type I), and to the detail requirements of ASTM D5363 (AN0411).

Cylinlock® 824 is a general purpose, single-component, anaerobic adhesive used primarily for joining cylindrical assemblies of all types. It is a low viscosity, self-hardening adhesive that cures when confined between ferrous or copper alloy metals. The cured adhesive is a thermoset plastic suitable for exposure to most solvents.

Cylinlock® 827 is a single component anaerobic retaining adhesive for cylindrical joints. The product cures when confined in the absence of air between close fitting metal surfaces. This product develops medium strength to facilitate disassembly.

Cylinlock® 842 is a high temperature, high strength anaerobic adhesive designed to retain and seal cylindrical assemblies. This compound will cure on metallic or non-metallic substrates and is suitable for exposure to most solvents.

Cylinlock® 845 is a fast curing, high strength anaerobic adhesive designed to retain and seal cylindrical assemblies. This compound will cure on metallic or non-metallic substrates and is suitable for exposure to most solvents and withstands temperatures of 300°F (149°C). Hernon Cylinlock® 845 cures quickly at room temperature without the need for surface activators or heat to join cylindrical assemblies. Fixturing strength develops in 24 hours. Hernon Primer 49 or 50 can be used to reduce fixturing time on inactive surfaces and to increase cure through gap. Certified to NSF/ANSI Standard 61 for use in commercial and residential potable water systems

Cylinlock® 846 is a fast-curing, high-strength anaerobic adhesive yielding higher shear strengths with temperature resistance up to 300°F (149°C). It provides relatively quick cures, outstanding solvent resistance, and improved reliability for metal service applications. Certified to NSF/ANSI Standard 61 for use in commercial and residential potable water systems.

Cylinlock® 94953 is a high-temperature, high strength anaerobic adhesive designed to retain and seal cylindrical assemblies. This compound will cure on metallic or non-metallic substrates and is suitable for exposure to most solvents.

External Ammunition Sealant 76081 is a single component U.V. anaerobic sealant. 76081 has a low viscosity penetrating material capable of bonding and sealing primers and case mouths in ammunition. This Sealant is specially formulated for Ammunition that needs greater fit tolerance and higher bullet pull forces. Curing occurs when the adhesive is applied between mating surfaces. The cured adhesive is a thermoset plastic and endures exposure to most solvents. Ammunition Sealant 76081 cures quickly at room temperature without the need for surface activators or heat to seal primer and case mouth assemblies. Fixturing strength develops in two to three minutes. Full strength will be reached in 24 hours. Cure fillets at UV light irradiances above 100 milliwatts/cm² to insure proper cure.

External Ammunition Sealant 76082 is a single component U.V. anaerobic sealant. 76082 has a low viscosity penetrating material capable of bonding and sealing primers and case mouths in ammunition. This Sealant is specially formulated for Ammunition that needs greater fit tolerance and higher bullet pull forces. Curing occurs when the adhesive is applied between mating surfaces. The cured adhesive is a thermoset plastic and endures exposure to most solvents. Ammunition Sealant 76082 cures quickly at room temperature without the need for surface activators or heat to seal primer and case mouth assemblies. Fixturing strength develops in two to three minutes, Full strength will be reached in 24 hours. Cure fillets at UV light irradiances above 100 milliwatts/cm² to insure proper cure.

Gasket Replacer 906 is a single component room temperature cure gel-like anaerobic gasketing compound formulated to provide instant sealing capabilities. Once cured between mating metal flanges filling voids in the surface, Gasket Replacer 906 provides a thin, flexible, solvent and temperature resistant seal. Gasket Replacer 906 can replace or be used as a dressing for conventional gaskets.

CM8005 is a single-component room temperature cure gel-like anaerobic gasketing compound formulated to provide instant sealing capabilities. Once cured between mating metal flanges and filling voids in the surface, CM8005 provides a thin, flexible, solvent and temperature resistant seal.

Gasket Replacer® 910 is a single component room temperature cure gel-like anaerobic gasket compound formulated to provide instant sealing capabilities. Once cured between mating metal flanges and filling voids in the surface, Gasket Replacer 910 provides a thin, flexible, solvent, and temperature-resistant seal. Gasket Replacer 910 is a recommended alternative to Gasket Eliminator Flange Sealant. Designed for metal closures Gasket Replacer offers a semi-flexible, anaerobic seal for flanges, similar to Loctite 515 and Loctite 518. Gasket Replacer's gel-like consistency can fill minor gaps and imperfections in flange surfaces and when fully cured, this sealant resists significant pressure. Known as a form-in-place gasket, this sealant adapts to the size and shape of the flange allowing a wide variety of uses including oil seals, engine housings and transmission flanges.

Gasket Replacer® 916 is a single component room temperature cure gel-like anaerobic gasket compound formulated to provide instant sealing capabilities. Once cured between mating metal flanges and filling voids in the surface, Gasket Replacer 916 provides a thin, flexible, solvent, and temperature-resistant seal. Gasket Replacer 916 can replace or be used as a dressing for conventional gaskets Gasket Replacer 916 is a recommended alternative to Gasket Eliminator Flange Sealant. Designed for metal closures Gasket Replacer offers a semi-flexible, anaerobic seal for flanges, similar to Loctite 515 and Loctite 518. Gasket Replacer's gel-like consistency can fill minor gaps and imperfections in flange surfaces and when fully cured, this sealant resists significant pressure. Known as a form-in-place gasket, this sealant adapts to the size and shape of the flange allowing a wide variety of uses including oil seals, engine housings and transmission flanges.

Grenade Igniter Case Sealant 40995 is a single component anaerobic thread locking and sealing adhesive. Grenade Igniter Case Sealant 40995 is a low viscosity penetrating material that works by capillary action between mating surfaces. The cured adhesive is a high-performance thermoset plastic suitable for temperatures up to 400°F (204°C). Grenade Igniter Case Sealant 40995 cures quickly at room temperature without the need for surface activators or heat to join threaded assemblies. Fixturing strength develops in five minutes, or within 10 seconds by exposing the edge fillets to high intensity long wavelength UV light (365 nm). Full strength will be reached in 24 hours. Cure fillets at UV light irradiances above 60 milliwatts/cm² to insure proper cure.

Porosity Sealant (HPS) 38374R is the solution to leak proof parts, improving machinability, in addition to increasing the durability and surface quality for painting and plating. The required addition of HPS Initiator activates the dual-cure system enabling the system to cure anaerobically at room temperature or at elevated temperatures. The cured, hardened resin exhibits superior chemical resistance and elevated temperature stability. The microscopic voids, where potential leaks occur (between metal grains or ceramic or plastic molecules) in the part are filled by low viscosity resin during vacuum application. Sealed micro-pores cure without shrinkage to a tough, cross-linked, thermoset polymer, permanently sealing the work piece. Residual adhesive film is washed from the part surfaces by water during the rinsing cycle. The parts leave the impregnating process without surface residue and can then be used in production within a short period of time. When used in preparation for plating or painting processes, the impregnation process also eliminates absorption of plating material (like acids) or painting prep solvents that could otherwise bleed out of the pores causing finishes to discolor, blister, pit or peel. Sealed powdered metal parts exhibit better machinability, enhanced tool life and better dimensional control.

Porosity Sealant (HPS) 59801 is a low viscosity liquid sealant designed for sealing interfacial leak paths in flexible electronic assemblies. It may also be used to enhance dielectric strength or seal porosity in passive materials. The dual-cure system incorporated in HPS 59801 offers the advantage of elevated temperature curing or curing at room temperature. HPS 59801 is typically applied with a vacuum impregnation process that removes air from the internal void and then saturates the part with liquid sealant. In the absence of circulating air, the liquid rapidly polymerizes to form a tough, flexible, thermoset polymer that permanently seals gaps in the assembly. Excess liquid sealant is rinsed from the outside of the part with an aqueous solution effectively leaving no surface build up. Parts processed with HPS 59801 are sealed internally but remain cosmetically and dimensionally unchanged. Typical applications include sealing or unitizing over-molded electrical components against leakage of air, water, coolants, oils and other fluids. As a good insulator, HPS 59801 may also be used to improve the dielectric strength across gaps between high voltage conductors.

Porosity Sealant (HPS) 990 is the solution to leak proof parts, improving machinability, in addition to increasing the durability and surface quality for painting and plating. HPS 990 is also excellent for sealing leak paths in rigid electronic assemblies. The hardened resins exhibit superior chemical resistance and elevated temperature stability. The microscopic voids, where potential leaks occur in the part are filled by the low viscosity resin during vacuum application. Sealed micropores cure without shrinkage to form tough cross-linked thermoset polymer, permanently sealing the piece. Excess residual adhesive is washed from the part surface during rinsing with water. The parts leave the impregnating process without surface residue and can then be used in production within a few short hours. The resin polymerizes, sealing gaps in any assembly. This protects electrical components against leakage from air, water, coolants and oils. When used in preparation for plating or painting processes, the impregnation process also eliminates absorption of plating materials (like acids) or painting prep solvents that could otherwise later bleed out of pores causing finishes to discolor, bleed, pit or peel. Sealed powdered metal parts exhibit better machinability, enhanced tool life and better dimensional control.

Porosity Sealant (HPS) 991R is the solution to leak proof parts, improving machinability, in addition to increasing the durability and surface quality for painting and plating. The required addition of HPS Initiator 91 activates HPS 991R enabling the system to cure at elevated temperatures (HPS 991R). The hardened resins exhibit superior chemical resistance and elevated temperature stability. The microscopic voids, where potential leaks occur (between metal grains or ceramic plastic molecules) in the part are filled by the low viscosity resin during vacuum application. Sealed micropores cure without shrinkage when exposed to elevated temperature to form tough cross-linked thermoset polymer, permanently sealing the workpiece. Residual adhesive film is water-washed from the part surfaces during rinsing. The parts leave the impregnating process without surface residue and can then be used in production immediately. When used in preparation for plating or painting processes, the impregnation process also eliminates absorption of plating materials (like acids) or painting prep solvents that could otherwise later bleed out of pores causing finishes to discolor, bleed, pit or peel. Sealed powdered metal parts exhibit better machinability, enhanced tool life and better dimensional control.

Porosity Sealant (HPS) 994 is the solution to leak proof parts, improving machinability, in addition to increasing the durability and surface quality for painting and plating. The hardened resins exhibit superior chemical resistance and higher temperature stability. The microscopic voids, where potential leaks occur (between metal grains or ceramic plastic molecules) in the part are filled by the low viscosity resin during vacuum application. Sealed micropores cure without shrinkage when exposed to elevated temperature to form tough cross-linked thermoset polymer, permanently sealing the workpiece. Residual adhesive film is water-washed from the part surfaces during rinsing. The parts leave the impregnating process without surface residue and can then be used in production immediately. When used in preparation for plating or painting processes, the impregnation process also eliminates absorption of plating materials (like acids) or painting prep solvents that could otherwise later bleed out of pores causing finishes to discolor, bleed, pit or peel. Sealed powdered metal parts exhibit better machinability, enhanced tool life and better dimensional control.

Porosity Sealant (HPS) 41814 is the solution to leak proof parts, improving machinability, in addition to increasing the durability and surface quality for painting and plating. The hardened resins exhibit superior chemical resistance and elevated temperature stability. The microscopic voids, where potential leaks occur (between metal grains or ceramic plastic molecules) in the part are filled by the low viscosity resin during vacuum application. Sealed micropores cure without shrinkage when exposed to elevated temperature to form tough cross-linked thermoset polymer, permanently sealing the workpiece. Residual adhesive film is water-washed from the part surfaces during rinsing. The parts leave the impregnating process without surface residue and can then be used in production immediately. When used in preparation for plating or painting processes, the impregnation process also eliminates absorption of plating materials (like acids) or painting prep solvents that could otherwise later bleed out of pores causing finishes to discolor, bleed, pit or peel. Sealed powdered metal parts exhibit better machinability, enhanced tool life and better dimensional control.

ReAct® 795 is a tough acrylic adhesive designed primarily for securing of ceramic permanent magnet segments in motor magnet bonding applications. This adhesive has also found wide acceptance in a variety of structural bonding applications due to its versatile performance capabilities. ReAct® 795 has demonstrated the ability to provide high tensile strength while maintaining excellent product flexibility. This results in tough, durable bonds with outstanding impact and peel resistance. This tough acrylic is a single component, room temperature curing adhesive which is used in conjunction with Activator 47. Additionally, exposure to a high intensity UV light will cure this adhesive to a dry, hard surface. ReAct® 795 is similar in function to Loctite A533 and Loctite AA332 and delivers high shear strength and tensile strength. One of its primary uses is securing permanent magnets in motor magnet bonding applications. Recomended Applications: Furniture | Elevators | Automotive Applications | Permanent Motor Magnets | Speakers | Generators | Bonding Flywheels | Sensors |

Self Locker 523 is a pre-applied micro-encapsulated adhesive for threaded fasteners. Self Locker 523 stays dry-to-the-touch until the shearing action of an engaging nut applied to the coated bolt causes the capsules to break allowing the adhesive to cure. This material securely locks and seals against vibration loosening and fluid leakage.

SelfSealer® 604 is a tough, pre-applied, non-hardening threaded sealant. When dried, it becomes a resilient, tight clinging, non-curing sealant for tapered or straight threads. It provides an instant seal on different pipe threads and can be used up to eight (8) times without recoating. SelfSealer® 604 is water based, non-toxic, safe and can be applied easily without special handling precautions. It provides resistance to vibrational loosening because of its prevailing torque characteristics. Therefore, it is very effective on non-locking applications.

SelfSealer® 615 is a high viscosity, tough, pre-applied, non-hardening threaded sealant. When dried, it becomes a resilient, tight clinging, non-curing sealant for tapered or straight threads. It provides an instant seal on different pipe threads and can be used up to eight (8) times without recoating. SelfSealer® 615 is water based, non-toxic, safe and can be applied easily without special handling precautions. It provides resistance to vibrational loosening because of its prevailing torque characteristics. Therefore, it is very effective on non-locking applications.

SelfSealer® 616 is a high viscosity, tough, pre-applied, non-hardening threaded sealant. When dried, it becomes a resilient, tight clinging, non-curing sealant for tapered or straight threads. It provides an instant seal on different pipe threads and can be used up to eight (8) times without recoating. SelfSealer® 616 is water based, non-toxic, safe and can be applied easily without special handling precautions. It provides resistance to vibrational loosening because of its prevailing torque characteristics. Therefore, it is very effective on non-locking applications.

SelfSealer® 618 is a tough, pre-applied, non-hardening threaded sealant. When dried, it becomes a resilient, tight clinging, non-curing sealant for tapered or straight threads. It provides an instant seal on different pipe threads and can be used up to eight (8) times without recoating. SelfSealer® 618 is water based, non-toxic, safe and can be applied easily without special handling precautions. It provides resistance to vibrational loosening because of its prevailing torque characteristics. Therefore, it is very effective on non-locking applications.

SelfSealer® 622 is a tough, pre-applied, non-hardening threaded sealant. SelfSealer® 622 provides an instant seal on different pipe threads and can be used up to eight (8) times without recoating. SelfSealer® 622 is water based, non-toxic, safe and can be applied easily without special handling precautions. SelfSealer® 622 provides resistance to vibrational loosening because of its prevailing torque characteristics. Therefore, it is very effective on non-locking applications.

Ultrabond® 3443 is a single component, tri-cure conformal coating formulated for bonding glass to glass or glass to metals. Ultrabond® 3443 is excellent for bonding and tacking many parts. Ultrabond® 3443 can also be cured with heat above 200°F (93°C) or Activator 56 or 59. Exposure to a high intensity UV light will cure these adhesives to a dry, hard surface.

Ultrabond® 55711 is a single component anaerobic and UV curable, paste-like sealing compound formulated to provide instant sealing and bonding of electrical connectors. Upon exposure to UV energy an outer cured skin will be formed to prevent migration of the sealant out of the connector during normal daily handling. The sealant inside of the skin maintains its original property. Upon insertion of the wire to the connector, the sealant in the connected area will cure to offer an environmentally resistant and secure connection.

Ultrabond® 71813 is a single component, tri-cure conformal coating formulated for bonding glass to glass or glass to metals. Ultrabond® 71813 is excellent for bonding and tacking many parts. Ultrabond® 71813 can also be cured with heat above 200°F (93°C) or Activator 56 or 59. Exposure to a high intensity UV light will cure these adhesives to a dry, hard surface.

Ultrabond® Sealant 721 is a UV curable adhesive that can be used to seal a variety of plastics when exposed to UV light. The sealant offers a water- tight seal with excellent environmental resistance. Prevents material escaping through a crimped seal. With Ultrabond® Sealant 721 a low powered UV lamp (Blacklight), can be used to inspect for the presence of adhesive on the substrates.

Ultrabond® 736 is a high impact UV curable structural adhesive formulated for bonding glass to glass, glass to metal and for potting and tacking applications. Ultrabond® 736 can also cure by heat or with activator. Ultrabond® 736 cures on exposure to ultraviolet light, with a wavelength of 365 nm, or with Hernon® Activator 56.

Ultrabond® 740 is formulated for bonding glass to glass or glass to metals. Ultrabond® 740 is excellent for bonding tacking and potting many parts. Ultrabond® 740 provides an excellent bond, high light transmittance and a refractive index like glass. Exposure to a high intensity UV light will cure these adhesives to a dry, hard surface.

Ultrabond® 748 is a single component 100% solid adhesive/sealant formulated to bond and seal electronic assemblies. Ultrabond® 748 can also be cured with heat above 200°F (93°C) or using a primer.

Ultrabond® 752 is a UV curable adhesive product that provides excellent adhesion to glass and to plastics such as polyester, PVC, cellulose acetate, or nylon.

Ultrabond® 758 Is a low viscosity self-leveling UV curable potting compound formulated to provide high performance, fast curing, coating and encapsulating of electronic components. This product is also used for shallow potting applications.

Ultrabond® 773 is a single component, tri-cure conformal coating formulated for bonding glass to glass or glass to metals. Ultrabond® 773 is excellent for bonding and tacking many parts. Ultrabond® 773 can also be cured with heat above 200°F (93°C) or EF Primer 56. Exposure to a high intensity UV light will cure these adhesives to a dry, hard surface.

Ultrabond® 774 is a one component adhesive which cures when exposed to ultraviolet radiation and/or visible light of sufficient intensity.

Ultrabond® 786 is an EB/UV curable product that provides excellent adhesion to a wide variety of substrates like metals, glass, ceramics and plastics. The sealant offers a water-tight seal with excellent environmental and high impact resistance.

UV FOG (Form on Gasket) 702 is an EB/UV curable product that provides excellent adhesion to shaft seals, oil seals, metals, glass, ceramics and plastics. Can be used as a Form-in-place gasket in oil and coolant systems. Typical applications include Engine covers, Oil pans and other fluid seal systems.

Hernon Voice Coil Bonder 360 is a single component, black, heat cure adhesive formulated for bonding and coating voice coil components and high-temperature lamination. The cured bond withstands temperatures exceeding 600°F (316°C).