Personal menu

2200 Dispensing Valve

The Sureshot® 2200 Series dispensing valve systems accurately control the application of most low to medium viscosity fluids. The unique seal-less design incorporates an inert polymer diaphragm that isolates the actuator from the valve. Valve open time can be as short as 15 milli-seconds. The adjustable open/close stroke 0.025 to 0.76mm (0.001” to 0.030”) means very fast response and positive shutoff. Sureshot® 2200 series dispensing valves are used for dispensing adhesives and sealants including ultraviolet curing polymers, anaerobics, cyanoacrylates, as well as lubricants and fluxes. An ultra violet light blocking Delrin® valve manifold with optional UV kit # 110-030 on the Sureshot® 2200 provides consistent trouble free dispensing of U.V. curing polymers.

SKU: SS2200PT

Variations *

Digital Downloads

Technical Data Sheet

Product tags

110-003 (1)
,
120000009 (1)
,
110-001 (1)
,
110-000 (1)
,
(48)

Customers who bought this item also bought

1 Liter bottle of External Ammunition Sealant 76081

External Ammo Sealant 76081

External Ammunition Sealant 76081 is a single component U.V. anaerobic sealant. 76081 has a low viscosity penetrating material capable of bonding and sealing primers and case mouths in ammunition. This Sealant is specially formulated for Ammunition that needs greater fit tolerance and higher bullet pull forces. Curing occurs when the adhesive is applied between mating surfaces. The cured adhesive is a thermoset plastic and endures exposure to most solvents. Ammunition Sealant 76081 cures quickly at room temperature without the need for surface activators or heat to seal primer and case mouth assemblies. Fixturing strength develops in two to three minutes. Full strength will be reached in 24 hours. Cure fillets at UV light irradiances above 100 milliwatts/cm² to insure proper cure.

Nuts N' Bolts® 420

Nuts N’ Bolts® 420 is a single component anaerobic thread locking material, which is thixotropic and develops low strength for easy disassembly. The product cures when confined in the absence of air between close fitting metal surfaces. Each batch of Nuts N’ Bolts® 420 is tested to the lot requirements of ASTM D5363 (AN0311) and complies with MIL-S-46163A (Type II Grade M).

Nuts N' Bolts® 423

Nuts N’ Bolts® 423 is a single component anaerobic thread locking material, which is thixotropic and develops medium strength. The product cures when confined in the absence of air between close fitting metal surfaces and is particularly suitable for less active substrates such a stainless steel and plated surfaces. Each batch of Nuts N’ Bolts 423 is tested to the lot requirements of ASTM D5363 (AN0321), and to the detail requirements of MIL-S-46163A (Type II Grade N).

R125 Reservoir

The R125 is a durable one gallon pressure reservoir is specifically designed for today’s production environment. The material output line is located in the center of the lid. This allows the dip tube to be centrally located so that an up to 1-gallon container can be directly placed into the reservoir. The lid design and single knob secure system permit quick changes or refills by operators and minimal clean up. The durable polyethylene material feed tube is resistant to most chemicals including adhesives, solvents, lubricants and sealants. The polyethylene feed tube is disposable and can be easily replaced. The material to be dispensed will only be in contact with the container and feed line.

2200 Dispensing Valve

External Ammo Sealant 76081

Nuts N' Bolts® 420

Nuts N' Bolts® 423

R125 Reservoir

Payment options

This website uses cookies.